Unfortunately, the length of your awning and your RV information does not tell me what the correct awning arm would be. I would need to know the manufacturer, pitch style and support arm length.
For instance, the Replacement Support Arm Assembly for Solera Flat RV Awnings # LC281154 you were looking at is a 69" support arm for a flat awning from Solera. If that is what you currently have, then this would be correct.
You could also have an awning from a different manufacturer or it could... view full answer...
Thank you for including the model number of your fan, 04751KS, which was exactly what was needed to find your replacement circuit board.
The correct part for your MaxxAir MaxxFan Plus Roof Vent 4751KS is:
- Replacement Printed Circuit Board for MaxxAir MaxxFan Plus Roof Vents # MA10A04751KS
This is the correct replacement circuit board for models 4751KS, 4761KS, and 4951KS. I have added a link to a video review for you to check out as well. view full answer...
Knowing the actual model number would be best so as to confirm you are ordering the correct part but, if you have the the MA00-04751KSX then we have the Replacement Printed Circuit Board for MaxxAir Powered Lift RV Roof Vents, # MA39FR. view full answer...
I suggest the Furrion RV Electric Fireplace with Logs - 40" Wide, # FF40SW15ABL. When installing the fireplace, you can either mount it fully into a cutout or cabinet opening. view full answer...
The Dexter 7K hubs feature an 8 on 6-1/2 inch bolt pattern, and use the 25580 inner/14125A outer bearing and 25520 inner/14276 outer race. They can either use the # GS-2250DL or the # GS-2125DL grease seals, so you'll want to pull one of the hubs and measure the diameter of the spindle where the grease seal rides. If the spindle is 2.125 inches, then you'd need the # GS-2125DL. If it's 2.25 inches, use # GS-2250DL.
The bearing kit needed will depend on that spindle diameter. If the journal... view full answer...
I have a solution for you, and while you can purchase front legs without the motors, the middle legs on the Lippert 6 point Ground Control 3.0 system # LC675817 are the same as the rear legs. Because of this, there is not going to be a replacement middle leg without the motor available.
In order to replace the middle leg, you'll want to measure the length of the outer tube on the jack leg to determine which leg will be the appropriate replacement. If your left middle leg measures 17"... view full answer...
The correct replacement transfer switch for your PD52 transfer switch in your 2019 Jayco North Point, is the:
- Progressive Dynamics Transfer Switch - Metal Case # PD52.
This transfer switch can automatically reroute your RV's AC input from shore power to generator power, and can also be use with an inverter in place of a generator.
Attached is a review video for you to check out as well. view full answer...
The Furrion RV Stereo, # DV1230BL is a good option as a replacement for your current DV1200 and a rather straight forward installation. It is not however a direct plug-in installation. This has a subwoofer terminal and will fit in a cut out that is 5-1/2 inches deep, 6-15/16 inches wide, and 4 inches tall, and overall the face measures 9-13/16 inches wide and 4-11/16 inches tall. view full answer...
The Command Electronics Lights # 328-003-85 & # 328-003-85L are the closest lights we have to the lights on your 2020 Jayco North Point 5th wheel. These lights do not have the reverse light function so they only have 3 wires.
If you wish to retain the reverse lights you can use 2 of the Dual LED Trailer Tail Lights # CE86FR. You will need a separate License Plate Mount # LPL56CB as these tail lights do not have the ability to also act as a license plate mount. view full answer...
The best way I can provide the proper wheel studs and lug nuts would be for you to drive out one of the existing studs and take some measurements off of it. There are several dimensions I will need in order to recommend the proper replacement for you.
I'll provide you a diagram showing the dimensions I need. Because these measurements need to be very precise, you'll want to use a digital caliper like part # PTW80157. I've also provided these dimensions for the # K916WB25, you can compare... view full answer...
The Replacement Door # AT91385 will fit your Atwood RV Water Heater # AT94022 (GC10A-4E) on your 2016 Jayco North Point 5th Wheel camper. view full answer...
Based on the GVWR of your 2019 Jayco North Point 315RLTS it does seem like you have 7k axles. I recommend verifying this information to be sure. These axles typically use the # 14125A outer and # 25580 inner bearing found in the Timken # TMK92VR. However, there are two different grease seal sizes used for this axle capacity so you will need to identify the correct grease seal before picking up a bearing kit.
The # TMK92VR uses a 10-36 seal with a 2.250" inner diameter. If you find that... view full answer...
I reached out to my contact at Lippert with the measurement of your support arm and they confirmed that the Replacement Short Arm Assembly for RV Awnings # LC97UD you were looking at is the correct replacement support arm assembly for your 2021 Jayco North Point 977RLBH with a Solera Power Awning. view full answer...
The Dexter Trailer Hub and Drum Assembly for 5,200-lb to 7,000-lb Axles - 8 on 6-1/2 - 9/16" Studs # 8-219-13UC3 will fit on your Lippert axle. They use the same size bearings and seal. view full answer...
With a Dexter 7,000lb axle and self adjusting electric trailer brakes you will likely have the Nev-R-Adjust Electric Trailer Brake Kit # 23-464-465. There is a small stamped area on the outside of the backing plate which will give you information on the brake assembly or if you have the serial number for your Dexter axle I can use that to verify all the parts installed on your axle from the factory. This will allow me to know exactly what grease seals, bearings and other parts you might... view full answer...